Lemon Balloon Garland Instructions - Pretty Collected

Lemon Balloon Garland Instructions

Thank you for ordering our Lemon Balloon Garland! 

Please follow the instructions below to create your own garland! 

Lemon Balloon Garland
When Should I Make My Balloon Garland?

Your balloon garland can be made 3-4 days prior to your event. However, it will look best if you make it as close to your event date as possible. Also, the sun can wash out the color of the balloons, especially the chrome balloons, so if you will be making your garland in advance, please store it out of the sun or out of direct sunlight. 

*TIP: Balloon garlands can take anywhere from 1-3 hours to make, depending on the length of the garland, so please make sure you allow for enough time to make it.

Blow Up Your Balloons:
How to Blow Up Balloons Using Qualatex Air Pump - Pretty Collected

If you ordered the balloon pump, then you will place the balloon on the pump, firmly hold the balloon onto the the tip of the pump (to prevent air leakage), and pump your balloon.

Be careful not to overfill your balloon or it will pop. You will get a sense, by looking at it, when it is close to full capacity. 

Once your balloon is filled take it off the pump and tie a knot.

* TIP: To create a more contoured balloon garland with depth, we recommend blowing up the 11 inch balloons in various sizes. If you blow all the 11 inch balloons up at full capacity, then the decorating strip may get really full in some areas making it hard to place multiple 11 inch balloons next to each other. 

* We also recommend blowing up all your balloons first, then attaching them to the balloon decorating strip.

How to Create a Round Balloon Versus an Oval Shaped Balloon:

How to Make a Balloon Round - Balloon Decorations - Pretty Collected

If you want to give the balloon a more rounded out shape, then you can lightly push the balloon against a table top or floor, all the while releasing just a little air to help give it shape. This will flatten out the top of the balloon, so it will have less of that oval shape that it will naturally create. Once you are happy with the size and shape, then tie a knot.

Attach Balloons to Balloon Decorating Strip:

How to Make a Gender Reveal Balloon Garland - Pretty Collected

(Photo was from another garland)

Leave the first two balloon holes empty - these will be used for attaching your balloon garland to the first command hook when you are ready to hang your garland. 

On the third hole begin attaching your balloons. You will first pull the balloon knot through the larger hole, then slide it to the left into the smaller hole.

* TIP: Be sure to only pull the balloon through to the knot. Do not pull past the knot as you will increase your chances of popping the balloon. 

DIY Balloon Garland Kit - Tropical Balloon Garland Instructions - Pretty Collected

Alternate sides in which you pull the balloons through the strip. This will give the balloon garland dimension. 

Also alternate the colors and sizes of the balloons you attach to the balloon decorating strip. 

When you are done, be sure to leave 2 holes at the other end of your balloon garland empty, so you can hang it on the Command hook. However, if you are creating a half arch, like the one we created in the main product image, then you can fill the balloons up to the very last hole. 

Exact sequence in which we added our balloons for this balloon garland:

Please keep in mind this is an 4 foot balloon garland, so you may have to alter it slightly depending on if you ordered a smaller or larger balloon garland. 

11 Inch Balloons:
3 White Balloons                                                                                                        

3 Lemonade Balloons                                                                                              

5 Inch:
3 White Balloons                                                                                                        

3 Lemonade Balloons

Repeat Pattern

Hang Your Garland:

Option 1: Hang on Command Hook Using First Hole on Strip

How to Hang Balloon Garland Using Command Hooks - Pretty Collected

(Photo was from another garland)

Place your first Command hook on the wall where you want your balloon garland to start. Give it a minute or two, then hang the first hole onto the Command hook. 

Option 2: Hang on Command Hook Using Twine

How to Hang a Balloon Garland Using Twine and a Command Hook - Pretty Collected

(Photo was from another garland)

If you want to give your balloon garland some extra length, or if it feels a little tight using the first hole to hang the strip onto the Command hook, then grab the twine included in your kit. Cut the twine and loop it through the first hole on the balloon decorating strip, then tie a knot. Grab the twine and hang it onto your Command hook.

Hanging a Small Garland - Straight Across:

If you are creating a smaller garland then you will place your second Command hook on the wall where you want the balloon garland to end.

Leave the Command hook on the wall a few minutes before hanging. Pull your balloon garland across to meet the second hook. If it fits perfectly, then you can place the last empty hole onto the hook. 

If it doesn't quite meet the Command hook, then use the string included in your kit to add length to your garland. Put the string through the last hole on your decorating strip. Pull the garland to where your Command hook is and estimate how much extra string you will need to get the strip to hang onto the hook. Then tie the string into a knot. Pull your garland across and hang!

How to Create a Balloon Garland - Gold Balloon Garland - Pretty Collected

DIY Balloon Garland - How to Hang It - Pretty Collected

HANGING A LARGER GARLAND - HALF ARCH: ACROSS WALL & CASCADES DOWNWARD:

If you are creating a larger garland then you will place your second Command hook on the wall where you want the balloon garland to curve, before it hangs down.

Leave the Command hook on the wall a few minutes before hanging. Pull your balloon garland across to meet the second hook. 

DIY Gender Reveal Balloon Garland - How to Hang a Balloon Garland - Pretty Collected

Use the string included in your kit to make a loop through your garland, where you want it to curve on the wall, and tie a knot.

How to Hang a Balloon Arch - DIY Balloon Garland - Gender Reveal Balloon Garland - Pretty Collected

Pull the garland upward, toward the hook, and hang the string on the hook. Adjust the placement of the string as needed. 

Now the balloon should look like a half arch where the rest of the garland hangs, allowing the balloons to cascade downward. 

MAKE ADJUSTMENTS, IF NEEDED:

Take a step back and admire all your hard work! If you love it, then you can leave it.

If you want to adjust the movement you can pull balloons forward or push some back. The balloons on the garland are pretty flexible. For example, if a gold balloon is hiding in the back you can swing it to the front and the garland will not fall apart. 

Also, if you want to adjust the color placement, then you can pull some balloons out of the holes and move swap them out with other balloons. 

ADD ANY REMAINING BALLOONS WITH GLUE DOTS:

If you have any leftover balloons and want to create more dimension, then feel free to take a glue dot, place it on a balloon, and add it to the balloon garland wherever you want. 

ADD LEMON BALLOONS:

Once you are done hanging the balloon garland, you can decide where you want to add in the lemon balloons. All you have to do is fill them up. Then take the end of the balloon and loop it through one of the holes on the strip where you want it to hang. You can secure it on to the strip with tape for extra support.